YIHUA 929D-V Electric Desoldering Soldering Iron Solder Sucker Desoldering Pump with Shorter Charging Handle and Desoldering Nozzles 1.0mm 1.2mm for Through-Hole Desoldering

7 reviews for YIHUA 929D-V Electric Desoldering Soldering Iron Solder Sucker Desoldering Pump with Shorter Charging Handle and Desoldering Nozzles 1.0mm 1.2mm for Through-Hole Desoldering

1. 

   William – October 7, 2025

   Works well for PCB’s with lots of pins.
   My step-son’s Switch controller needed a new joystick. As an amateur electronics kit builder, I figured, “no problem”, but there were 14 pins needing to be un-soldered. I’ve used a solder-sucker before, but this looked like it might be too much work for what I had.This tool served as both the soldering iron and sucker at the same time, so no switching back-and-forth. For this reason, it would be worth the price if I expected to use it often. For me, it will probably get used only very occasionally, but it’s nice to keep with the other DIY electronic tools just in case.It was easy to clean out the bits, and at came with three extra tips, though I haven’t needed any others than the one installed. It had enough power to melt the solder on both sides of the PCB, and sucked it right through the hole, needing to be re-applied on only a few of the 14 pins. It’s handle was very ergonomic, fitting my hand well, making it easy to de-solder and trigger the suction with one hand. The only problem that took getting used to was holding the tip against the PCB. The spring action of the piston tended to make the tip bounce off of the board, preventing the suction from working. Some careful pressure solved that problem with a few tries.

2. 

   Amazon Customer – October 7, 2025

   Xbox X joystick replacement
   Works great, preheat for at least 3 minutes. If you can’t get all the solder out of the pin holes I added solder into the gun itself until it was covering the nozzle hole. Then I applied it to the pin with Flux and it would clean the stubborn solder off. Easy to use one handed and beats using desoldering wick hands down.

3. 

   Sam Fisher – October 7, 2025

   Solid Desoldering Tool (But Don’t Expect Miracles)
   This YiHua desoldering iron is a pretty solid tool. It’s super easy to use and heats up quickly, melting solder in a flash. The metal tip is a big improvement over those teflon ones that always seem to burn or melt. Plus, it’s easy to clean and doesn’t clog up easily. For it’s current price point, it’s a good middle-ground option between those cheap solder suckers and the pricier desoldering guns.Now, here’s the thing: it works way better than those manual solder suckers, but it doesn’t have the super-powerful suction I was hoping for. For components with two leads, it usually gets the solder out in one go. But sometimes it takes a few tries, even with through-hole contacts.With bigger components, like transistors or capacitors, you’ll probably need to do several cycles of melting and sucking to get all the solder out. Holding it on the joint for longer helps melt the solder thoroughly, but be careful not to overheat the component.I didn’t have any issues with the tip fitting over different sized leads, from tiny resistors to larger transistors and capacitors. It works best on two-lead components because the leads can move freely as the solder melts. With three-lead components, it’s a bit trickier.Overall, this tool is definitely a step up from a basic solder sucker, but don’t expect the same vaccum as one one a complete rework station. If you’re looking for a decent, affordable desoldering tool, this one gets the job done, just be prepared to put in a bit of extra work on those stubborn joints.—Product: YiHua 929D-V Electric Desoldering Soldering Iron Solder Sucker Desoldering Pump with Shorter Charging Handle and Desoldering Nozzles 1.0mm 1.2mm for Through-Hole DesolderingASIN: B094ZCRXMN

4. 

   Trevor Book – October 7, 2025

   Great desoldering pump
   I had a solenoid version desoldering pump previously. It finally kicked the bucket on me. I bought this manual heated pump because it was cheap and in hopes that it would outlast of mechanical one. So far, it works great.

5. 

   Michael – October 7, 2025

   So worth it
   Omg! I should have bought this long time ago. It has helped sooooo much. I’ve desoldered boards in minutes that have taken so much time using wicks.

6. 

   Steven Vee – October 7, 2025

   A Good Quality Solder Remover At Reasonable Cost
   The Yihua 9290-V Electric Desoldering Iron offers a significant improvement over copper braid (wick) and manual, non heated solder suction methods.As an experienced electronic bench technician, I have often had problems removing all of the solder from the legs of transistors, capacitors, resistors and other devices mounted via through-holes in circuit boards. I have found that there is often no substitute for a heated solder sucking device such at the Yihua unit.Heat output is very good, even for melting and removing larger solder blobs. If removing solder from very fine or extremely heat sensitive devices, there are outboard, plug-in adjustable power reduction devices, similar to light dimmers, that can be used to reduce the tip temperature of the desoldering unit as needed. Also, having a removable, replaceable tip is a definite advantage.The solder sucker portion is easily removed from the heating section of the iron and emptied. Invest in some silicon oil to keep the O-ring and inside barrel of the solder sucker lubricated. This will optimize the sucking action of the unit by reducing internal friction, and it will greatly extend its useful life.As other reviews have mentioned, the Yihua Desoldering Iron puts out a notable quantity of smoke when it is first powered up. Place it outside in non-flammable surroundings when first powering it up for ten minutes or so or until the unit no longer smokes (and don’t breathe in the smoke, just to be safe). Once this is done, the unit should no longer smoke when you plug it in, later.The Yihua 9290-V Desoldering Iron has been working well for me. Recommended.

7. 

   Gonzo gonzalez – October 7, 2025

   Hasta el momento a sido de gran ayuda.Facilidad al desoldar componentes electrónicos..Muy práctico funciona bien.Ahorra tiempo….👍