Saker Honing Guide with Whetstone – Red Off-Center Upgraded Honing Tool and Diamond Sharpening Stone Set Kit for Knife, Short Chisels and Planes, Fine/Coarse Plate, 400/1000/Grit…

13 reviews for Saker Honing Guide with Whetstone – Red Off-Center Upgraded Honing Tool and Diamond Sharpening Stone Set Kit for Knife, Short Chisels and Planes, Fine/Coarse Plate, 400/1000/Grit…

1. 

   John of WV – November 16, 2025

   Works well with short blades.
   I bought this to sharpen a spokeshave blade due to its stated ability to accommodate short chisels. It work just as advertised. Of particular use is its ability to be used from both sides. I’m happy with it.

2. 

   David B. – November 16, 2025

   Excellent kit.
   The wider roller is an improvement.

3. 

   RPT – November 16, 2025

   Great but key design flaw
   The basic function of the sharpener works well, and I have cleaned up some old construction chisels that are close to razor sharp. That said there is a fundamental design flaw that will often leave chisel edges angled when sharpened as the angle guide uses the backside of the chisel to create the datum for the chisel edge. I have a nice set of Marples chisels that I sharpened, and when I noticed the angle on the finished edge, I measured the thickness of the chisel with a caliper from left to right across the backside that rests against the angle guide, and the thickness varies up to 0.25mm. As the chisel rests on the angle guide on this backside surface, it will inevitably result in angling the sharpened surface. The only way to adjust for this is to manually shim the backside of the chisel resting against the angle guide to make sure the sharpened edge is laying absolutely flat against the stone. Not an easy task! Otherwise this kit works fine and will deliver a sharpened edge. Note that I also finish the edges on a 3000 and then 8000 grit stone.

4. 

   Blue Pansy – November 16, 2025

   good quality and easy to use
   I have no past experience with working with these diamond sharpeners. This was easy to use and the roller worked very nice to sharpen the end of chisel. It appears to be good quality to me and I thought the price was okay. The base did slide on me so I had to hold the base. It was nice to be able to flip the diamond bar over for the 2 different grits. I may need more grits when I know how to sharpen better. This should last a long time unless I am not using it properly.

5. 

   Cousin DuPree – November 16, 2025

   Sharpness is next to Godliness . . .
   Seems perfect to me. Easily adjusted for both chisels and plane blades, two fixed angles are easy to use. My third Sakar tool and each has been well-made and accurate at an affordable price.

6. 

   R. Bliss – November 16, 2025

   Well worth the money!
   Much better than the small wheel guide.

7. 

   BryanC – November 16, 2025

   Diamond stone is not flat with a poorly machined jig
   I like the self centering jig being made of aluminum but it lacks refinement in its tolerances. The jaws are loose within their track. This leads the chisel, in this case, not being square to the jig itself.The kit I bought came with a 400/1000 grit “diamond” stone. The quality of this stone is sub-par at best. By the time I sharpened 6 chisels the stone had lost its ability to effectively sharpen. Here’s the kicker, the stone is warped. After transitioning from 400 to 1000 you can see in the photo, after using marking dye, the 1000 grit side is bowed, raised in the center. I used a straight edge and I could rock it side to side a 1/32″.I would recommend just buying the jig and buy a set of better stones. Even then you’ll have to double check for square.

8. 

   Jeff – November 16, 2025

   Gets chisel faces dead flat, mirror-polishing if you want
   Got this to straighten out my woodworking tools. Consistency is beyond anything I could do free-hand, especially on something like a 6mm chisel where it’s really difficult to feel a face registering flat.From flattening on 80-grit sandpaper all the way up to a 6000-grit water-stone for a mirror-polish, you can literally read text in the reflection, and it’s dead flat; no waviness on the edges that sometimes happens free-handing it. I flatten all the faces then put it in the guide and begin back at the bottom of the grit ladder, 80 or 150 to flatten, then 1000-grit water stone and 6000 to polish.To be fair, to completely re-face the 1″ chisel by hand took probably 2-3 hours and 5-6 sheets of 80-grit. It can be done with the honing guide if you have the patience.Once it’s flat, it takes maybe 20-30 minutes on the 1000-grit just cause I skip a lot of grits in between; (only had low-grit paper and two-sided water-stone). Then 10-15 minutes maybe on the 6000-grit for a mirror polish, depends on the size of the chisel too. That’s all for a full-reface though, once it’s done, it’s much faster to do touch ups on a secondary 30 degree bevel after the 25 degree has been established.In that 3 hours, the chisel didn’t move once after it was locked into the guide, only thumb-tightened. It doesn’t required much pressure if you let the grit do the work. If you really put weight into it, it might slip but muscle is unnecessary imoWould recommend that you go through all the grits in one go after setting the chisel in the guide. There’s no real way to set the chisel exactly back in the spot where it was if you mess with it in between grits. You can get close but we’re talking a couple microns for dead flat mirror polish and if you tweak it in between you’ll throw off the alignment. You’ll notice your polish line will be ever so slightly higher or lower if you mess with it in between. Might not be a big deal depending but something to noteIf you’re going to use it on slab+low-grit, it helps to put a piece of tape or paper down to protect the roller. On a polishing stone, it mostly just glides without damaging the face of the roller.Oiled the bearings regularly, idk if they’ll rust from being used on a water-stone; looks like the pin can be hammered out so if they need to be cleaned or replaced should be easy enoughFor me, it fit a 6mm chisel, all the way up to a 2″ plane blade.A minor issue is the roller is so closely machined to the body that it can accumulate lint/metal shavings in between the body and the roller. It’s easy enough to dust out but with a little more clearance is probably avoidable altogether.Only wish there was a jig included to set degrees, like made of plastic or such. I’m definitely going to ruin the instruction sheet with the reference markings on it, so will have to make my own jig for 25 and 30 degrees before I lose the instruction sheet.Small issues aside, it works very well so far. Can’t comment on longevity. Hopefully it’ll last cause I can see this being one of those ‘if it goes missing I’d buy it again immediately’ items. Do not even want to attempt free-handing small chisels again after seeing how accurate a sharpening jig really is.

9. 

   FRANCK9522 – November 16, 2025

   Idéal pour affuter ciseaux a bois

10. 

    Markus Hackl – November 16, 2025

    + Die Verarbeitung ist sehr gut+ Es lassen sich einfach sehr gute Ergebnisse erzielen+ Die Laufrolle läuft gut und liegt durch ihre Breite sehr stabil auf+ Von kleinen Stechbeiteln (6mm) bis zu Hobeleisen lässt sich alles einspannen- Die Halterung ist aus Aluminium, wodurch im Laufe der Zeit die Funktion nicht mehr ideal istAn sich eine super Erweiterung in meinem Schleifzubehör. Einmal eingestellt und schon kann jeder ein gutes Ergebnis erzielen, ohne lang nachzudenken oder Angst zu haben, etwas falsch zu machen.Für den Preis ist die Qualität sehr gut. Wer etwas noch Stabileres will, muss wohl einfach bereit sein, mehr zu zahlen.

11. 

    Andoni – November 16, 2025

    Funciona tal y como se esperaba. El material es robusto y es muy fácil darle el ángulo deseado a los filos. Contiene una pequeña guia de papel donde te indica las medidas exactas y las posiciones para obtener los ángulos del filo deseados.

12. 

    Daniel Guzman Hernandez – November 16, 2025

    Muy buena herramienta muy estable,proporciona afilado fino

13. 

    David J. Higgins – November 16, 2025

    Now this is a good quality item. Not perfect but close enough for the DIYer.